| Input | Operating Voltage | 198-264VAC 50Hz /60Hz |
| Rated Input Voltage | 220-240VAC 50Hz /60Hz |
| DC Input Voltage range | 200-240VDC |
| Input Current | 0.33A Max. |
| Input Inrush Current | <15A (Half current pulse width 100US) @230VAC |
| Power Factor | ≥0.95 @230VAC (Full load) |
| Total harmonic distortion | Typical: 13% (@230Vac, 100% load) |
| No-load power | ≤0.5W |
| Stand-by Power | ≤0.5W(@230Vac when PUSH or DALI turn off) |
| Efficiency | 86%Max. @230VAC (Full load) |
| Wiring Method | Push terminal, wire cross section:0.75-1.5mm2 |
| Automatic circuit breaker (Calculate current in the wire) | type | C10 | C13 | C16 | C20 | C25 |
| Number | 25 | 30 | 40 | 50 | 66 |
| type | B10 | B13 | B16 | B20 | B25 |
| Number | 15 | 20 | 25 | 28 | 30 |
| Output | Operating mode | Constant Current |
| Load type | LED |
| Flickering / Flickering-Free | Flicker value: less than 2% for whole dimming range |
| Start up time | <1s (@230Vac) |
| No-load output voltage | 68VDC Max. |
| Load output voltage range | 2*(6-58VDC) |
| Full load output power | 2*30W Max. |
| Load output current | 2*350~900mA : For details<Current gear setting> |
| Constant current/voltage Precision | Constant Current Precision ±5% |
| Wiring method | Push terminal, wire cross section:0.75-1.5mm2 |
| Control Method | Primary PUSH Dimming | Primary PUSH dimming (Max.lead length:20M) |
| 1-10V Dimming | 1-10V dimming(Port current＜1MA)
(Max.lead length:20M) |
| Dimming Range | Primary PUSH & DALI dimming: 0%-100%
1-10V dimming:2%-100% |
| Primary PWM Dimming | 1-10V port PWM dimming (3KHZ-8KHZ) |
| Potentiometer | Yes, 100kΩ |
| DALI Dimming | DALI dimming (Max.lead length:300M) |
| Exception Protection Requirements | Output over temperature
protection | Yes, without self recovery function(Can be inquired) |
| Output short circuit protection | Yes, without self recovery function(Can be inquired) |
| Operating Environment | Operating temperature/ humidity | -25℃~50℃ Humidity:85% (Non-condensing) |
| Storage temperature/ humidity | -40℃~80℃, Humidity:10%–95% |
| Max. case temp(Tc) | 85℃ |
| Safety & EMC | EMC standard | EN55015 EN61547 EN61000-3-2 EN61000-3-3 |
| DALI protocol standard | IEC62386-102 IEC62386-207 DT6 |
| Safety standard | EN61347-1 EN61347-2-13 |
| Certification | ENEC SEMKO CB CE |
| Withstand voltage | 3750Vac, 5mA, 60s (Input “L N”- Output “SEC”) |
| Others | Degrees of protection | IP20 |
| Type of protection | Class II |
| Installation type | Independent installation |
| Installation dimension | 202*58*30mm |
| Blackout memory function | Yes, PUSH blackout memory |
| PUSH dimming synchronization | 20 units Max. |
| Packaging requirement | white box+ Instructions Clapboard Outer Carton(K=A) |
| Weight | 245g |
| Life | 50000h @Ta full load |
| Note: All parameters are tested at the input voltage of 230Vac and 25 degree environment unless specified. |
